Reward
- 1 Quest Point.
- 7,500 Smithing XP, 7,500 Crafting XP.
- Ability to make and equip the Elemental Mind Equipment. |
 Start PointExam centre at the Dig Site. Members Only |
Difficulty:
Length:
 |
Requirements
Skill: 20 Magic, 30 Smithing.
Quest: Elemental Workshop I.
Item: 2 Elemental Bars (8 Coal and 2 Elemental Ores), Hammer.
Recommendations
Skill: 45 Magic (for Teleport to Camelot).
Item: Camelot Teleport Runes, Pickaxe.
Amongst the ancient scrolls and papers held at the Dig Site's Examination Centre, scholars have discovered more references to the mysterious elemental ore. Recently they have uncovered a beaten book, detailing long-lost uses for this odd material.
Can you decrypt the code that will lead you to the deeper depths of the Elemental Workshop? Can you get your head around fixing the mind-bending machinery, or will you fry your brain in the attempt?
Part 1:
Another Workshop
Step 1
Snatch the beaten book and read it.
Go to the workshop and follow the note.
Search the pipe for a key and use it to go downstairs.
To start this quest you will need to head to the Exam Center in the Dig Site south-east of Varrock. Once there, search the bookcases in the south-east corner of the examination room (Picture). You should find a Beaten Book. Keep this with you since you will need it later on to smith the Mind Helm.
Read the book and you will receive a "note," with directions to the new workshop from the stairs down to the old one. Teleport to Camelot, go to Seers' and enter the Elemental Workshop from the first quest (if you lost your key you can search the bookcase upstairs across the road to obtain it) (Picture).
Once you arrive there, follow the steps listed within the note. If you follow the directions correctly, you will find yourself in the water chamber and to the east of a pipe. Search it to receive another key (Picture). This key unlocks a door near the entrance to the Workshop that leads downward (Picture).
The new workshop is square-shaped with a cart track running around the perimeter. There are four broken machines on each side of the square. There are also two staircases leading up to the catwalk area of the new Workshop. Your task in the quest is to repair the four machines in the workshop and then to "prime" an Elemental Bar.
Part 2:
Repairing the Machinery
Step 2
Make 2 elemental bars and smith one into a claw.
Lower the claw and fix it.
Search crates for a pipe and replace the broken one.
Search the schematics crate for the plans on how to fix and make a claw (Picture). Now head back up to the first Workshop and mine an elemental ore. As with the first quest, you will need to kill an Earth Elemental (level-35) to obtain the ore. To save returning here for another bar later on, get two ores and make two bars.
Once you've mined the ores, go and smelt them into two bars using the furnace, then smith one bar into a claw using the workbench in the center room and return to the second workshop. Click the lowering lever (making certain the crane is facing to the north) and use the elemental bar on the claw to repair it (Picture).
To fix the Pipes, you will need to pick up a spare pipe. This is in a random crate somewhere in the workshop, so look around for it. Use the pipe on the broken pipes at the far northern side of the catwalks (Picture).
Step 3
Search crates for the 3 cogs.
Place the cogs on the pins.
Rearrange the pipes in the Junction Box.
To fix the Wind Tube on the eastern side of the second Workshop, you need to find three different cogs: a Large cog, a Medium cog and a Small cog.
These cogs can be found in crates throughout the new Workshop. The locations of the different size cogs differ player-to-player. Use the Small cog on the upper left pin, the Medium cog on the lower left pin and the Large cog on the right pin (Picture). Operate the lever to make sure you did it right. If you did it correctly it should say "the fan is now blowing".
To repair the Steam Press on the western side of the new Workshop, climb up onto the catwalks and find the Junction Box on the western side. Open the Junction box (Picture) and arrange the pipes as shown in the picture to fix the Steam Press. All the machines will now fixed (Picture).
Part 3:
An Elemental Mind Shield
Step 4
Follow the steps to get the claw to pick up the bar.
Heat the bar in the lava.
Flatten the bar.
Before priming an Elemental Bar, make sure the Wind Fan is not operating. Click the lever that operates the Jig-cart until the cart is positioned underneath the repaired crane. When the cart arrives at the claw use your Elemental Bar with the cart (Picture). Lower the claw so it picks the bar up, then raise the claw with the same lever.
Click the other lever to swivel the Crane over the lava and then click the lowering lever again to lower it into the lava. Click the lowering lever once more to raise the bar up, click the rotating lever to swivel it back to the cart and lower it. Raise it one last time so that the claw is no longer holding the bar and the heated bar will be on the cart (Picture).
Operate the Jig-cart again. The cart should position itself beneath the Steam Press. Operate the Steam Press' lever which is in front of the pipes on the first floor. The Elemental Bar should now be flattened, as long as the pipes in the Junction Box was positioned correctly (Picture).
Step 5
Cool the bar, empty the tank and close the door.
Fan the bar off and pick it up with the claw.
Operate the Jig-cart again so that it moves around to the Water Tank. Open the tank door and click the corkscrew lever twice to expand and retract the Cart Rack. Once the cart is inside the tank, close the door. Now operate the two valves so that the tank fills with water, cooling the bar down (Picture).
Once cooled, empty the tank by turning the valves again (standing in front of it turn the right valve first to release the water followed by the left valve to get rid of all water), open the door and release the rack again. Once the cart is back on the track, retract the rack and close the door.
Operate the Jig-cart once again so that it heads towards the Wind Tunnel. Operate the fan's lever so that the bar is fully cooled down. Turn the fan off by operating the lever again and make your way over to the Jig-cart lever. Click this for the last time to move the cart back underneath the crane. Once it reaches here, retrieve the Primed Bar from the cart (Picture).
Step 6
Go into the mind room and use the extraction gun.
Smith the bar into a mind helmet.
Before starting this step, make sure you have your Beaten book in your inventory. Head down the stairs in the north-west corner of the new Workshop. From the stairs head south and then east through the Mind Door.
Once in the Mind Room, use your Primed Bar on the Extraction Gun and operate the Extractor (Picture). Note: you will lose 20 magic levels when using the extractor.
You will now receive an Elemental Mind Bar (Picture). Return upstairs to the first workshop and use your new bar on the workbenches and create a Prime Elemental Helmet to complete the quest.
| 
OSRS RuneScape Help
RuneScape Community Forums
Skill Guides
Quest Guides
City Guides
Guild Guides
Mini Game Guides
Treasure Trail Help
Miscellaneous Guides
Dungeon Maps
Mining Maps
Items Database
Monsters Database
Shops Database
Tome/Books Database
Skill Calculators
Coordinate Locator
Zchat Clan Chat
Stuck on something? Want some more tips? Ask on our forums.
